View MBT801-S_4312141.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet
Specification MBT801-S
SSC
Drawn Approval
Approval
Rev. 00 November 2007 www.ZLED.com
Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet
MBT801-S
1. Features 2. Absolute Maximum Ratings
3. Electro Characteristics 4. Optical characteristics 5. Outline Dimension 6. Packing 7. Soldering 8. Precaution for use 9. Handling of Silicone Resin LEDs
Rev. 00 November 2007 www.ZLED.com
Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet Technical Data Sheet
MBT801-S
Description This surface-mount LED comes in PLCC standard package dimension. It has a substrate made up of a molded plastic reflector sitting on top of a bent lead frame. The die is attached within the reflector cavity and the cavity is encapsulated by epoxy or silicone The package design coupled with careful selection of component materials allow these products to perform with high reliability in a larger temperature range -40 to 100. The high reliability feature is crucial to Automotive interior and Indoor ESS.
MBT801-S
Features
* Industry Standard PLCC SMT package * High brightness using AlInGaP and InGaN dice technologies * Available in multiple colors * High volume, high reliability
Applications
* Interior automotive * Electronic Signs and Signals * Office Automation, Electrical Appliances, Industrial Equipment
Rev. 02 09 December 2006 April 2008 www.ZLED.com
Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet
1. Features * BLUE colored SMT package * Material InGaN/SiC * Suitable for all SMT assembly methods Suitable for all soldering methods * RoHS Compliant
Rev. 00 November 2007 www.ZLED.com
Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet
2. Absolute maximum ratings
Parameter Power Dissipation Forward Current Peak Forward Current Reverse Voltage Operating Temperature Storage Temperature Symbol Value 120 30 90 5 -40 ~ +100 -40 ~ +100 Unit mW mA mA V
oC oC
Pd IF IFM *2 VR Topr Tstg
*1 Care is to be taken that power dissipation does not exceed the absolute maximum rating of the product. *2 IFM was measured at TW 1msec of pulse width and D 1/10 of duty ratio.
3. Electric characteristics
Parameter Forward Voltage Reverse Current Luminance Intensity *1 Peak Wavelength Dominant Wavelength Spectral Bandwidth 50% Viewing Angle *2 2 Symbol Condition Min 2.7 70 464 Typ 3.2 335 465 470 23 120 Max 4.0 10 600 476 Unit V A mcd nm nm nm deg.
VF IR IV P d
1/2
IF =20mA VR=5V IF =20mA IF =20mA IF =20mA IF =20mA IF =20mA
*1. The luminous intensity IV was measured at the peak of the spatial pattern which may not be aligned with the mechanical axis of the LED package. Luminous Intensity Measurement allowance is 10% *2. 21/2 is the off-axis where the luminous intensity is 1/2 of the peak intensity.
Rev. 00 November 2007 www.ZLED.com
Relative Luminous Intensity Iv/Iv [Rel]
Forward Current IF [mA]
Forward Current IF [mA]
Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet
4. Optical characteristics
Forward Current vs. Forward Voltage
100
Relative Luminous Intensity vs Forward Current
1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0
(Ta=25 OC )
(Ta=25 OC )
10
1
2.6
2.8
3.0
3.2
3.4
3.6
3.8
4.0
0
5
10
15
20
25
30
Forward Voltage VF (V)
Forward Current IF [mA]
Forward Current Derating Curve
40
Radiation Diagram
(Ta=25 OC )
0
30
-30
30
20
-60
60
10
-90
0
-40 -20 0 20 40 60 80 100 120
90
Ambient Temperature TA [OC]
Rev. 00 November 2007 www.ZLED.com
Cathode Cathode Mark 2.2
( Tolerance: 0.2, Unit: mm )
6. packing
1.750.1 2 .0 0 .0 5 4 .0 0 .1 1 .5 5 0 .0 5 0 .2 2 0 .0 5
3.50.1
80.1
5
1 .0 0 .1 3 .1 0 .1
8
3.830.1
2 .2 2 0 .1
11.4 0.1 180 +0 -3 2.0 0.2
LABLE 13 0.2
9.0 0.3
30
10
22
(1) Quantity : 2000pcs/Reel (2) Cumulative Tolerance : Cumulative Tolerance/10 pitches to be 0.2mm (3) Adhesion Strength of Cover Tape : Adhesion strength to be 0.1-0.7N when the cover tape is turned off from the carrier tape at the angle of 10 to the carrier tape (4) Package : P/N, Manufacturing data Code No. and quantity to be indicated on a damp proof Package
60
1.8
Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet
5.outline dimension
Recommended Solder Pattern
2.8 2.2 0.15 0.8 1.9 0.8 Anode 1.8 1.6
3.2 2.4 1.6
Rev. 00 November 2007 www.ZLED.com
Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet
Reel Packing Structure
Reel
QUANTITY : XXXX LOT NUMBER : XXXXXXXXXX PART NUMBER :
SEOUL SEMICONDUCTOR CO., LTD.
HUMIDITY INDICATOR DESI PAK
Aluminum Vinyl Bag
QUANTITY : XXXX LOT NUMBER : XXXXXXXXXX PART NUMBER :
SEOUL SEMICONDUCTOR CO., LTD.
Outer Box Structure
Material : Paper(SW3B(B)) SIZE (mm) TYPE a c b 7inch 245 220 142
1 SIDE c
QUANTITY : XXXX LOT NUMBER : XXXXXXXXXX PART NUMBER :
SEOUL SEMICONDUCTOR CO., LTD. RoHS
1
b
a
Rev. 00 November 2007 www.ZLED.com
Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet
7. soldering
(1) Lead Solder
Lead Solder
Lead Solder Pre-heat Pre-heat time Peak-Temperature Soldering time Condition 120~150 120 sec. Max. 240 Max. 10 sec. Max.
2.5~5 C / sec.
2.5~5 o C / sec. Pre-heating 120~150 oC
240 oC Max. 10 sec. Max. 60sec. Max. Above 200 oC
120sec. Max.
(2) Lead-Free Solder
Lead-frame Solder
Lead Free Solder Pre-heat Pre-heat time Peak-Temperature Soldering time Condition 150~200 120 sec. Max. 260 Max. 10 sec. Max.
1~5 o C / sec.
1~5 o C / sec. Pre-heating 150~200 o C
260 oC Max. 10 sec. Max. 60sec. Max. Above 220 oC
120sec. Max.
(3) Hand Soldering conditions Do not exceed 4 seconds at maximum 315C under soldering iron.
(4) The encapsulated material of the LEDs is silicone. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter, the picking up nozzle that does not affect the silicone resign should be used.
Note : In case that the soldered products are reused in soldering process, we don't guarantee the products.
Rev. 00 November 2007 www.ZLED.com
Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet
8. precaution for use
(1) Storage In order to avoid the absorption of moisture, it is recommended to store in a dry box (or a desicator) with a desiccant. Otherwise, to store them in the following environment is recommended. Temperature : 5C ~30C Humidity : maximum 70%RH (2) Attention after open. LED is correspond to SMD, when LED be soldered dip, interfacial separation may affect the light transmission efficiency, causing the light intensity to drop. Attention in followed; Keeping of a fraction Temperature : 5 ~ 40C Humidity : less than 10% (3) In the case of more than 1 week passed after opening or change color of indicator on desiccant, components shall be dried 10-12hr. at 605C. (4) Any mechanical force or any excess vibration shall not be accepted to apply during cooling process to normal temperature after soldering. (5) Quick cooling shall be avoided. (6) Components shall not be mounted on warped direction of PCB. (7) Anti radioactive ray design is not considered for the products. (8) This device should not be used in any type of fluid such as water, oil, organic solvent etc. When washing is required, IPA should be used. (9) When the LEDs are illuminating, operating current should be decided after considering the ambient maximum temperature. (10) The LEDs must be soldered within seven days after opening the moisture-proof packing. (11) Repack unused products with anti-moisture packing, fold to close any opening and then store in a dry place. (12) The appearance and specifications of the product may be modified for improvement without notice.
Rev. 00 November 2007 www.ZLED.com
Z-Power LED X10490 Z-Power LED X10490 Technical Data Sheet
9. Handling of Silicone Resin LEDs
(1) During processing, mechanical stress on the surface should be minimized as much as possible. Sharp objects of all types should not be used to pierce the sealing compound.
(2) In general, LEDs should only be handled from the side. By the way, this also applies to LEDs without a silicone sealant, since the surface can also become scratched.
(3) When populating boards in SMT production, there are basically no restrictions regarding the form of the pick and place nozzle, except that mechanical pressure on the surface of the resin must be prevented. This is assured by choosing a pick and place nozzle which is larger than the LED's reflector area. (4) Silicone differs from materials conventionally used for the manufacturing of LEDs. These conditions must be considered during the handling of such devices. Compared to standard encapsulants, silicone is generally softer, and the surface is more likely to attract dust. As mentioned previously, the increased sensitivity to dust requires special care during processing. In cases where a minimal level of dirt and dust particles cannot be guaranteed, a suitable cleaning solution must be applied to the surface after the soldering of components. (5) SSC suggests using isopropyl alcohol for cleaning. In case other solvents are used, it must be assured that these solvents do not dissolve the package or resin. Ultrasonic cleaning is not recommended. Ultrasonic cleaning may cause damage to the LED. Rev. 00 November 2007 www.ZLED.com

▲Up To Search▲

Price & Availability of MBT801-S

	To Download MBT801-S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .